Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Category Filter
Brake Disc / Rotor Slotted 2-pc FRONT 997 GT3 Cup Car - A1-126S
A1-126S
Vehicle Group
- Porsche 997 MK1 GT3 2007-09
- Porsche 997 MKII GT3 2010-11
Information
Brake Disc / Rotor Slotted 2-pc FRONT
Fits:
Front rotor: 380mm Direct Replacement
Porsche 997 GT3 Cup Car
Kit Contains:
Brake Disc 380 complete with centre bell.
Brake Disc Type: 2-Piece Slotted
The Girodisc system is a direct replacement for the OE disc on all 997.2 GT3/GT2's, with or without the OEM PCCB rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency.
The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from our own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.
The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.
Once the Girodisc system is in place, simply replace the cast iron rotor when needed.
Fits:
Front rotor: 380mm Direct Replacement
Porsche 997 GT3 Cup Car
Kit Contains:
Brake Disc 380 complete with centre bell.
Brake Disc Type: 2-Piece Slotted
The Girodisc system is a direct replacement for the OE disc on all 997.2 GT3/GT2's, with or without the OEM PCCB rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency.
The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from our own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.
The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.
Once the Girodisc system is in place, simply replace the cast iron rotor when needed.
Prices from: £786.00
Related products
Vehicle Group
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005-08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
- Porsche 997 MKII Carrera C2S 3.8L 2009-12
- Porsche 997 MKII Carrera C4S 3.8L 2009-12
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
Information
Titanium Brake Pad Heat Shields.
This Product Fits:
Porsche 986 Boxster S 3.2 99-05 Front
Porsche 987 Boxster S 3.2 05>> Front
Porsche 987C Cayman 06>> Front
Porsche 996 3.4/3.6 97-05 Front
Porsche 997 3.6L C2/C4* 05-09 Front
*Not S 3.8L
Porsche 997 3.6L C2/C4* 09>> Front
*Not S 3.8L
Porsche 996 C4S 02-05 Rear
Porsche 996 GT2 02-05 Rear
Porsche 996 GT3 MKI 99-01 Rear
Porsche 996 GT3 MKII 02-05 Rear
Porsche 996 3.6LTurbo 02-05 Rear
Porsche 997 3.8L C2S/C4S 05-09 Rear
The problem of brake fluid boiling is simply traced to heat transferring from the rotors and pads directly into the fluid through the caliper pistons. When brake fluid boils, it releases air that is normally part of the molecular structure of the fluid. This air is compressible of course, and the brake pedal goes to the floor instead of moving the caliper pistons. Production cars tend to suffer from this on track days more as they don't usually have the extensive cooling duct and exotic brake materials as true racing cars. True racing only brake calipers generally come with titanium caliper pistons for one reason. Titanium as a material has low thermal conductivity. This means that it is very bad at transferring heat, which is fantastic if you are trying to keep your fluid cool.
The Girodisc solution to help prevent fluid boiling is to use a thin titanium shim placed between the pad back and the pistons, to keep the braking heat from transferring into the pistons and fluid. Here is a comparison of materials and their relative thermal conductivity ratings:
Titanium 6AL-4V 6.7 W/mk
Steel 52 W/mk
Aluminum 130 W/mk
You can see that Titanium will transfer far less heat than steel and especially aluminum. For cars that are going to see hard or multiple track days, these shims are cheap protection from losing the pedal due to boiling at the wrong time and making the day very expensive.
Water jet cut to exact size, no cutting, grinding, or swearing involved.
Price is per axle (four pieces)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
TS-917-4
The product you are viewing cross references to these numbers
This Product Fits:
Porsche 986 Boxster S 3.2 99-05 Front
Porsche 987 Boxster S 3.2 05>> Front
Porsche 987C Cayman 06>> Front
Porsche 996 3.4/3.6 97-05 Front
Porsche 997 3.6L C2/C4* 05-09 Front
*Not S 3.8L
Porsche 997 3.6L C2/C4* 09>> Front
*Not S 3.8L
Porsche 996 C4S 02-05 Rear
Porsche 996 GT2 02-05 Rear
Porsche 996 GT3 MKI 99-01 Rear
Porsche 996 GT3 MKII 02-05 Rear
Porsche 996 3.6LTurbo 02-05 Rear
Porsche 997 3.8L C2S/C4S 05-09 Rear
The problem of brake fluid boiling is simply traced to heat transferring from the rotors and pads directly into the fluid through the caliper pistons. When brake fluid boils, it releases air that is normally part of the molecular structure of the fluid. This air is compressible of course, and the brake pedal goes to the floor instead of moving the caliper pistons. Production cars tend to suffer from this on track days more as they don't usually have the extensive cooling duct and exotic brake materials as true racing cars. True racing only brake calipers generally come with titanium caliper pistons for one reason. Titanium as a material has low thermal conductivity. This means that it is very bad at transferring heat, which is fantastic if you are trying to keep your fluid cool.
The Girodisc solution to help prevent fluid boiling is to use a thin titanium shim placed between the pad back and the pistons, to keep the braking heat from transferring into the pistons and fluid. Here is a comparison of materials and their relative thermal conductivity ratings:
Titanium 6AL-4V 6.7 W/mk
Steel 52 W/mk
Aluminum 130 W/mk
You can see that Titanium will transfer far less heat than steel and especially aluminum. For cars that are going to see hard or multiple track days, these shims are cheap protection from losing the pedal due to boiling at the wrong time and making the day very expensive.
Water jet cut to exact size, no cutting, grinding, or swearing involved.
Price is per axle (four pieces)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
TS-917-4
23329
07.B314.15
07B31415
99635294903
99735193904
The product you are viewing cross references to these numbers
Price: £74.87
In stock
Vehicle Group
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005-08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
Information
Titanium Brake Pad Heat Shields.
This Product Fits:
Porsche 986 Boxster 2.5/2.7 97-05 Rear
Porsche 986 Boxster S 3.2 99-05 Rear
Porsche 987 Boxster 2.7 05>> Rear
Porsche 987 Boxster S 3.2 05>> Rear
Porsche 987C Cayman 06>> Rear
Porsche 996 3.4/3.6 97-05 Rear
Porsche 997 C2/C4 05-09 Rear
The problem of brake fluid boiling is simply traced to heat transferring from the rotors and pads directly into the fluid through the caliper pistons. When brake fluid boils, it releases air that is normally part of the molecular structure of the fluid. This air is compressible of course, and the brake pedal goes to the floor instead of moving the caliper pistons. Production cars tend to suffer from this on track days more as they don't usually have the extensive cooling duct and exotic brake materials as true racing cars. True racing only brake calipers generally come with titanium caliper pistons for one reason. Titanium as a material has low thermal conductivity. This means that it is very bad at transferring heat, which is fantastic if you are trying to keep your fluid cool.
The Girodisc solution to help prevent fluid boiling is to use a thin titanium shim placed between the pad back and the pistons, to keep the braking heat from transferring into the pistons and fluid. Here is a comparison of materials and their relative thermal conductivity ratings:
Titanium 6AL-4V 6.7 W/mk
Steel 52 W/mk
Aluminum 130 W/mk
You can see that Titanium will transfer far less heat than steel and especially aluminum. For cars that are going to see hard or multiple track days, these shims are cheap protection from losing the pedal due to boiling at the wrong time and making the day very expensive.
Water jet cut to exact size, no cutting, grinding, or swearing involved.
Price is per axle (four pieces)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
TS-738-4
The product you are viewing cross references to these numbers
This Product Fits:
Porsche 986 Boxster 2.5/2.7 97-05 Rear
Porsche 986 Boxster S 3.2 99-05 Rear
Porsche 987 Boxster 2.7 05>> Rear
Porsche 987 Boxster S 3.2 05>> Rear
Porsche 987C Cayman 06>> Rear
Porsche 996 3.4/3.6 97-05 Rear
Porsche 997 C2/C4 05-09 Rear
The problem of brake fluid boiling is simply traced to heat transferring from the rotors and pads directly into the fluid through the caliper pistons. When brake fluid boils, it releases air that is normally part of the molecular structure of the fluid. This air is compressible of course, and the brake pedal goes to the floor instead of moving the caliper pistons. Production cars tend to suffer from this on track days more as they don't usually have the extensive cooling duct and exotic brake materials as true racing cars. True racing only brake calipers generally come with titanium caliper pistons for one reason. Titanium as a material has low thermal conductivity. This means that it is very bad at transferring heat, which is fantastic if you are trying to keep your fluid cool.
The Girodisc solution to help prevent fluid boiling is to use a thin titanium shim placed between the pad back and the pistons, to keep the braking heat from transferring into the pistons and fluid. Here is a comparison of materials and their relative thermal conductivity ratings:
Titanium 6AL-4V 6.7 W/mk
Steel 52 W/mk
Aluminum 130 W/mk
You can see that Titanium will transfer far less heat than steel and especially aluminum. For cars that are going to see hard or multiple track days, these shims are cheap protection from losing the pedal due to boiling at the wrong time and making the day very expensive.
Water jet cut to exact size, no cutting, grinding, or swearing involved.
Price is per axle (four pieces)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
TS-738-4
21792
07.B315.14
07B31514
99635293903
The product you are viewing cross references to these numbers
Price: £74.87
In stock