Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Category Filter
Bump steer correcting tie rod kit. Porsche 964 Turbo - 2180033
2180033
Vehicle Group
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
Information
Bump steer correcting tie rod kit.
1 kit, req'd per car.
For Porsche 964 1989-94 Turbo Wide-Body Only
Bump Geometry Correction
Lowered cars with non-RS wheel carriers suffer from bump steer and will benefit from bump geometry correction.
Bump steer is a change in toe due to vertical movement of the wheel, such as when driving over a bump. The toe change causes the car to turn, and the driver needs to constantly correct for this to maintain a steady trajectory. This makes the car a handful to drive, especially over bumpy road surfaces.
Bump correction is achieved by moving the tie rod end pivot about 10mm closer to the steering knuckle as compared to the stock tie rod end. This changes the angle of the tie rod to produce the bump geometry correction.
No Need To Convert Wheel Carriers
This Bump Steer Correcting Tie Rod kit provides bump geometry correction with the standard C2/C4 wheel carriers. It is not necessary to convert the wheel carriers to RS type to correct for bump steer when using our kit.
• Corrects for bump steer
• Eliminates rubber inner-joint
• Enhanced driving precision
• Easier and more cost effective than RS wheel carrier conversion
These Elephant Racing bump steer tie rods also eliminate the compliant rubber inner-joint found in the factory 964 tie rods with a spherical bearing providing a more direct and responsive steering feel. Thus, proper suspension geometry is restored, driver corrections are minimized, and vehicle trajectory is stabilized making driving control easier while reducing driver fatigue.
Out Performs All Other Tie Rods
Even on cars fresh from the Porsche factory assembly lines our anti-bump steer kit will reduce bump steer through the full range of motion.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
2180033
The product you are viewing cross references to these numbers
1 kit, req'd per car.
For Porsche 964 1989-94 Turbo Wide-Body Only
Bump Geometry Correction
Lowered cars with non-RS wheel carriers suffer from bump steer and will benefit from bump geometry correction.
Bump steer is a change in toe due to vertical movement of the wheel, such as when driving over a bump. The toe change causes the car to turn, and the driver needs to constantly correct for this to maintain a steady trajectory. This makes the car a handful to drive, especially over bumpy road surfaces.
Bump correction is achieved by moving the tie rod end pivot about 10mm closer to the steering knuckle as compared to the stock tie rod end. This changes the angle of the tie rod to produce the bump geometry correction.
No Need To Convert Wheel Carriers
This Bump Steer Correcting Tie Rod kit provides bump geometry correction with the standard C2/C4 wheel carriers. It is not necessary to convert the wheel carriers to RS type to correct for bump steer when using our kit.
• Corrects for bump steer
• Eliminates rubber inner-joint
• Enhanced driving precision
• Easier and more cost effective than RS wheel carrier conversion
These Elephant Racing bump steer tie rods also eliminate the compliant rubber inner-joint found in the factory 964 tie rods with a spherical bearing providing a more direct and responsive steering feel. Thus, proper suspension geometry is restored, driver corrections are minimized, and vehicle trajectory is stabilized making driving control easier while reducing driver fatigue.
Out Performs All Other Tie Rods
Even on cars fresh from the Porsche factory assembly lines our anti-bump steer kit will reduce bump steer through the full range of motion.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
2180033
2180033
96534703200
96434703203
96534703201
96434703201
The product you are viewing cross references to these numbers
€772.20
Now €694.98
In stock
Related products
Information
Rennline Rubber boots for use with spherical end links.
For use with adjustable control arms
Full encapsulating weather/dust seals are an option with this kit to provide extra protection against the dirty driving conditions both under the car and behind the front wheels. These will work with all Rennline control arms and bump steer kits.
Sold in Pairs
Fits Rod end sizes Male: 1/2", 5/8", 3/4", 14mm, 16mm, 18mm
Female: 1/2", 5/8", 3/4", 14mm, 16mm, 18mm
For use with adjustable control arms
Full encapsulating weather/dust seals are an option with this kit to provide extra protection against the dirty driving conditions both under the car and behind the front wheels. These will work with all Rennline control arms and bump steer kits.
Sold in Pairs
Fits Rod end sizes Male: 1/2", 5/8", 3/4", 14mm, 16mm, 18mm
Female: 1/2", 5/8", 3/4", 14mm, 16mm, 18mm
€28.08
Now €25.27
In stock