Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Your Vehicle
Porsche // 992 (911) MK1 2019-2024 // 992.1 GT3 CUP 4.0L 2021-24
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Category Filter
Bumper horn piping seal. Porsche 911/912 - PCG91118240
PCG91118240/1
Vehicle Group
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Bumper horn piping seal. 1m.
(1m front and 1m rear needed)
This flexible rubber beading trims and seals the interface between the bumper horn (overrider) and the main bumper body, providing a clean, finished look and helping protect against moisture, dirt, and minor abrasion.
Fits:
Porsche 911 2.0-2.4 01/1963 - 07/1973
Porsche 912 1.6 01/1965 - 02/1970
Diagram ref no 9
The piping seal installs easily into the original grooves and mounting channels on the bumper profile, forming a neat protective edge that enhances both aesthetic and functional performance. It is ideal for classic restoration projects, bumper reassembly after removal, or when refreshing aging or brittle original piping.
The bumper horn piping seal bridges the gap between the chrome/painted bumper horn and the adjacent bodywork by providing a soft, contoured edge. It helps:
• Mask raw edges and transitions between components
• Protect surrounding paint and finishes from minor contact damage
• Reduce the ingress of dirt, water, and road debris behind the bumper trim
• Restore the classic factory-correct appearance of the bumper assembly.
Function:
Installed along the perimeter of the overrider (horn) section of the front or rear bumper, this rubber piping compresses slightly to grip the bumper and horn edges. Its profile maintains a consistent seal while allowing normal flex and vibration without loss of fit - preventing rattles and movement that can occur with brittle, aged original beading.
With age, original bumper horn piping often becomes brittle, cracked, deformed, or lost, exposing underlying edges and hardware. This can detract from the vehicle’s appearance and allow water and debris to sit behind the bumper, potentially trapping moisture and accelerating corrosion. Replacing it with an OE Match seal restores the look and function of the factory assembly - preserving both style and protective qualities.
When to replace:
• Original piping is cracked, shrunken, or missing
• Bumper horn or overrider has been removed for service
• Preparing a vehicle for restoration, sale, or show
• When reassembling bumped or replaced bumper trim
• Preventive refresh on aging rubber components
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PCG91118240
The product you are viewing cross references to these numbers
(1m front and 1m rear needed)
This flexible rubber beading trims and seals the interface between the bumper horn (overrider) and the main bumper body, providing a clean, finished look and helping protect against moisture, dirt, and minor abrasion.
Fits:
Porsche 911 2.0-2.4 01/1963 - 07/1973
Porsche 912 1.6 01/1965 - 02/1970
Diagram ref no 9
The piping seal installs easily into the original grooves and mounting channels on the bumper profile, forming a neat protective edge that enhances both aesthetic and functional performance. It is ideal for classic restoration projects, bumper reassembly after removal, or when refreshing aging or brittle original piping.
The bumper horn piping seal bridges the gap between the chrome/painted bumper horn and the adjacent bodywork by providing a soft, contoured edge. It helps:
• Mask raw edges and transitions between components
• Protect surrounding paint and finishes from minor contact damage
• Reduce the ingress of dirt, water, and road debris behind the bumper trim
• Restore the classic factory-correct appearance of the bumper assembly.
Function:
Installed along the perimeter of the overrider (horn) section of the front or rear bumper, this rubber piping compresses slightly to grip the bumper and horn edges. Its profile maintains a consistent seal while allowing normal flex and vibration without loss of fit - preventing rattles and movement that can occur with brittle, aged original beading.
With age, original bumper horn piping often becomes brittle, cracked, deformed, or lost, exposing underlying edges and hardware. This can detract from the vehicle’s appearance and allow water and debris to sit behind the bumper, potentially trapping moisture and accelerating corrosion. Replacing it with an OE Match seal restores the look and function of the factory assembly - preserving both style and protective qualities.
When to replace:
• Original piping is cracked, shrunken, or missing
• Bumper horn or overrider has been removed for service
• Preparing a vehicle for restoration, sale, or show
• When reassembling bumped or replaced bumper trim
• Preventive refresh on aging rubber components
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PCG91118240
PCG91118240
64450539405
99991118240
The product you are viewing cross references to these numbers
Price: £12.00
In stock