do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
The single sensor unit is for cars that already have a separate crankshaft sensor, either on the flywheel, or an existing crank pulley sensor
Fits:
Porsche 911 2.7 - 1974 to 1978 (CIS injection)
Porsche 911 SC 3.0ltr - 1978 to 1983
Porsche 911 3.2 Carrera - 1984 to 1989
Single sensor – This unit has a singe sensor inside the body that detects one single tooth. This shaft rotates at half engine speed, so this sensor picks up once every 720 degrees. This is used to tell the ECU when it is on the compression stroke. The single sensor version needs to be used in conjunction with an existing crank position sensor, either on the pulley, or on the flywheel as common on the 964/993 or cars that have had their flywheel machined for a sensor pickup
Why do you need this system and what is a crankshaft position sensor?
When converting classic Porsches to modern electronic fuel injection, the engine control unit (ECU) needs to know exactly where the crankshaft and camshaft is in its 4 stroke cycle and how fast they are spinning. This allows the ECU to correctly time each spark and fuel injector opening time and duration. A sensor is pointed at the crankshaft pulley or flywheel and measures a pulse for every tooth. There is one missing tooth and from this the ECU can work out what the crankshaft position is relative to this missing tooth. The time between pulses gives the engine speed and rate of change.
The 3.2 Carrera / 964 / 993 already have a sensor on the flywheel to measure crankshaft position so these engines only require one senor for camshaft positioning. This sensor is installed in the body our module, and measures a single tooth at the top of the drive shaft. As this is installed in the distributor hole, this is geared to run at half engine speed, so will produce a pulse once every 720 degrees. With these two sensors, the ECU knows the exact position the engine is in its 4 stroke cycle. And now, we can run accurate sequential injection and ignition.
Our kit uses high speed digital hall effect sensors for a digital output to the engine control unit, these are best run at 8V, most modern ECU's have an 8V output dedicated for crankshaft sensors.
Machined aluminium housing and anodised finish, complete with maintenance free bronze bush and sealed for life roller bearing. These sensors are quite adjustable so are often able to be used with existing crank pully and trigger wheel setups from other quality vendors.
Sync 1 Sensor Kit Includes:
- Main body assembly
- ZF Hall effect sensors, single tooth for engine cycle sensing x 1
- Wiring and connectors, with pins and connectors for connecting to your wiring loom.
For use when you already have some other crankshaft position sensing either on the flywheel or pulley and just need to add an engine cycle/sync sensor to complete your sequential system.
This replacement kit fits to the OEM distributor location using your own factory distributor gear. Simply remove the factory distributor gear from your install the gear, wire to your ECU, fine tune the sensor air gap to the crank trigger disc, setup the reference position in the ECU and you have all the sensing you need for the latest sequential fuel and ignition systems. This kit works on the 964, 993 and with the turbo distributor gears.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060250052
The product you are viewing cross references to these numbers
- Porsche 955 Cayenne 3.2L V6 2003-06
- Porsche 958 Cayenne V6 3.6L Petrol (300Hp) 2010-17
Fits:
Porsche 955 Cayenne 3.2L 2004-05
Click 'Zoom in' for large parts diagram.
Diagram ref no 31
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95560612510
The product you are viewing cross references to these numbers
- Porsche 958 Cayenne V6 3.6L Petrol (300Hp) 2010-17
- Porsche 95B.1 Macan S Petrol 3.0L V6 (340Bhp) 2014-18
- Porsche 95B.1 Macan Turbo 3.6L V6 (400Bhp) 2014-18
Sold EACH.
Fits:
Porsche 958 Cayenne 3.6L V6 Turbo / Turbo GTS 2015-18
Porsche 95B Macan S 3.0L / Turbo 3.6L 2014-18
Diagram ref no 13
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94660610600
The product you are viewing cross references to these numbers
Electrical plug housing - multiple applications (see below).
Porsche 986 Boxster 1997-04
- Camshaft position sensor
- Throttle valve
- Ignition coil
Porsche 996 Carrera & GT3 1998-05
- Ignition coil
Porsche 964/993 Carrera & Turbo 1994-98
- Crankshaft position sensor
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99965291640
The product you are viewing cross references to these numbers