Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Category Filter
Clutch kit. Porsche 997 TURBO 3.6L / 3.8L M97.70 Clutch Plate, Pressure Plate - 99711691350
99711691350/2
Vehicle Group
- Porsche 997 MK1 TURBO 2007-09
- Porsche 997 MKII Turbo 2010-13
Information
Clutch kit contains:
Clutch plate, Pressure plate & release bearing
Fits:
Porsche 997 MKI 3.6l Turbo 2007>>
Porsche 997 MKII 3.8L M97.70 Turbo 2009>>
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99711691350
The product you are viewing cross references to these numbers
Clutch plate, Pressure plate & release bearing
Fits:
Porsche 997 MKI 3.6l Turbo 2007>>
Porsche 997 MKII 3.8L M97.70 Turbo 2009>>
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99711691350
99711691350
3000950125
3000951025
3082213136
1878003310
4200080060
The product you are viewing cross references to these numbers
Price: €677.94
In stock
Related products
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Oil seal - crank rear
Fitting Position: Transmission End,
Inner Diameter: 90 mm,
Outer diameter: 110 mm,
Width: 12 mm, Radial Shaft Seal Design.
Fits:
Porsche 911 3.0L 1978 - 1983
Porsche 911 3.2L 1984 - 1989
Porsche 930 Turbo 1975 - 1989
Diagram Ref No 33
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911342642
The product you are viewing cross references to these numbers
Fitting Position: Transmission End,
Inner Diameter: 90 mm,
Outer diameter: 110 mm,
Width: 12 mm, Radial Shaft Seal Design.
Fits:
Porsche 911 3.0L 1978 - 1983
Porsche 911 3.2L 1984 - 1989
Porsche 930 Turbo 1975 - 1989
Diagram Ref No 33
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911342642
99911342641
99911326440
99911346140
99911342640
99911342642
The product you are viewing cross references to these numbers
Price: €74.84
In stock
Vehicle Group
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 924 2.0L 1976-79
- Porsche 924 2.0L 1980-85
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Clutch alignment tool.
This tool is necessary for a professional assemblage of the clutch.
Fits:
For Vehicles with manual transmission
Porsche 356
Porsche 911 F
Porsche 911 G (1 of 3 possible variants, this has 24 teeth)
Porsche 924 2.0 L (except Turbo)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
1087
The product you are viewing cross references to these numbers
This tool is necessary for a professional assemblage of the clutch.
Fits:
For Vehicles with manual transmission
Porsche 356
Porsche 911 F
Porsche 911 G (1 of 3 possible variants, this has 24 teeth)
Porsche 924 2.0 L (except Turbo)
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
1087
1087
The product you are viewing cross references to these numbers
Price: €23.80
In stock
Vehicle Group
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
Rear main oil seal - crank rear.
Fitting Position: Transmission End
Inner Diameter: 90 mm, Outer diameter: 110 mm, Width: 12 mm
Radial Shaft Seal Design.
Fits:
Porsche 911 3.0L 1978 - 1983
Porsche 911 3.2L 1984 - 1989
Porsche 930 Turbo 1975 - 1989
Diagram Ref No 33
The rear main oil seal fits at the rear of the crankshaft where it passes through the engine case. It helps retain engine oil inside the crankcase and prevents oil from leaking into the flywheel, clutch, or transmission bellhousing area.
Functions
• Replaces the rear crankshaft oil seal
• Helps seal the rear of the engine crankshaft
• Helps prevent engine oil leaks from the bellhousing area
• Protects the clutch and flywheel area from oil contamination
• Supports correct crankcase oil retention
• Replaces hardened, worn, split, leaking, or damaged original seals
• OE Match replacement for Porsche 911 and 930 engine service.
Why Replace This Part?
Rear main oil seals are exposed to heat, crankshaft rotation, oil, pressure changes, and age-related wear. Over time, the seal can harden, shrink, crack, wear, or lose sealing ability. A failed rear main seal may cause oil leaks between the engine and gearbox, oil contamination on the clutch, burning oil smells, or visible oil dripping from the bellhousing area. Replacing the seal helps restore a clean, reliable crankshaft seal.
When to Replace This Part
• Oil is leaking from between the engine and gearbox
• Oil drips are visible from the bellhousing area
• The clutch or flywheel is contaminated with oil
• The engine or gearbox has been removed
• The flywheel is being removed or replaced
• The original seal is hardened, worn, split, or leaking
• Preventative replacement is being carried out during clutch or engine service.
Where it fits on the car
This oil seal fits at the rear crankshaft position on Porsche 911 and 930 engines. It sits between the crankshaft and engine case, behind the flywheel area.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911342641
The product you are viewing cross references to these numbers
Fitting Position: Transmission End
Inner Diameter: 90 mm, Outer diameter: 110 mm, Width: 12 mm
Radial Shaft Seal Design.
Fits:
Porsche 911 3.0L 1978 - 1983
Porsche 911 3.2L 1984 - 1989
Porsche 930 Turbo 1975 - 1989
Diagram Ref No 33
The rear main oil seal fits at the rear of the crankshaft where it passes through the engine case. It helps retain engine oil inside the crankcase and prevents oil from leaking into the flywheel, clutch, or transmission bellhousing area.
Functions
• Replaces the rear crankshaft oil seal
• Helps seal the rear of the engine crankshaft
• Helps prevent engine oil leaks from the bellhousing area
• Protects the clutch and flywheel area from oil contamination
• Supports correct crankcase oil retention
• Replaces hardened, worn, split, leaking, or damaged original seals
• OE Match replacement for Porsche 911 and 930 engine service.
Why Replace This Part?
Rear main oil seals are exposed to heat, crankshaft rotation, oil, pressure changes, and age-related wear. Over time, the seal can harden, shrink, crack, wear, or lose sealing ability. A failed rear main seal may cause oil leaks between the engine and gearbox, oil contamination on the clutch, burning oil smells, or visible oil dripping from the bellhousing area. Replacing the seal helps restore a clean, reliable crankshaft seal.
When to Replace This Part
• Oil is leaking from between the engine and gearbox
• Oil drips are visible from the bellhousing area
• The clutch or flywheel is contaminated with oil
• The engine or gearbox has been removed
• The flywheel is being removed or replaced
• The original seal is hardened, worn, split, or leaking
• Preventative replacement is being carried out during clutch or engine service.
Where it fits on the car
This oil seal fits at the rear crankshaft position on Porsche 911 and 930 engines. It sits between the crankshaft and engine case, behind the flywheel area.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911342641
99911342641
99911326440
99911346140
99911342640
The product you are viewing cross references to these numbers
€14.28
Now €12.85
Orderable