Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Category Filter
Forged JE piston and liner kit 105mm, 24mm pin. Porsche 914/ VW Type 4 - VW105T4JE
VW105T4JE
Vehicle Group
- Porsche 914 (1970-1976)
Information
This is a new set of Type 4 105mm flat top JE Pistons and cylinders.
JE Forgings are made from 2618 Aluminum, They have a 0 offset with extra material under the top for the valve pockets. The Big Bore Cylinders are honed in house to exact tolerances. This set comes with a 34.6mm Compression Height and the 24mm Pin. The slightly smaller compression height allows you to easily build small stroked engines 71 to 78mm with the Standard length rods that have the 24mm pins giving you the option to Build 2.4L and bigger Engines. This is a Machine in kit you will need to open both the Heads and Case to install them.
Engine Type : Porsche 914, VW Type 4, Bus or Sandrail.
Engine size: 2458cc with 71mm crank
Stroke: 71 to 78mm
Cylinders: Cast Iron
Pistons: Forged JE
Compression Height: 34.60mm
Pin: 24mm
Set includes: 4 pistons, 4 cylinders, 4 pins and a set of rings
JE Forgings are made from 2618 Aluminum, They have a 0 offset with extra material under the top for the valve pockets. The Big Bore Cylinders are honed in house to exact tolerances. This set comes with a 34.6mm Compression Height and the 24mm Pin. The slightly smaller compression height allows you to easily build small stroked engines 71 to 78mm with the Standard length rods that have the 24mm pins giving you the option to Build 2.4L and bigger Engines. This is a Machine in kit you will need to open both the Heads and Case to install them.
Engine Type : Porsche 914, VW Type 4, Bus or Sandrail.
Engine size: 2458cc with 71mm crank
Stroke: 71 to 78mm
Cylinders: Cast Iron
Pistons: Forged JE
Compression Height: 34.60mm
Pin: 24mm
Set includes: 4 pistons, 4 cylinders, 4 pins and a set of rings
€1,321.84
Now €1,189.66
Orderable
Related products
Vehicle Group
- Porsche 356 1950-55
Information
This is a new set of 80mm Porsche 356 pistons and cylinders.
It fits 356 Pre A Porsches 1948-55 with the early 2 piece Case.
The Cylinders are cast iron with Graphite Coated Hypereutectic pistons with valve pockets, and the 22mm Pin. This kit requires no machine work, when installing in a factory Porsche case & heads
It is also commonly used as a big bore supplement for the early 36 Horse VW Engine, but requires a lot of machine work.
Engine size: 1500cc
Stroke: 74mm
Cylinders: Cast Iron.
Pistons: Hypereutectic
Dome CC: 0
Piston Angle: Flat top
Kit includes:4 Cylinders, 4 Pistons, A set of Piston Rings, and 4 wrist pins and clips.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0081180S
The product you are viewing cross references to these numbers
It fits 356 Pre A Porsches 1948-55 with the early 2 piece Case.
The Cylinders are cast iron with Graphite Coated Hypereutectic pistons with valve pockets, and the 22mm Pin. This kit requires no machine work, when installing in a factory Porsche case & heads
It is also commonly used as a big bore supplement for the early 36 Horse VW Engine, but requires a lot of machine work.
Engine size: 1500cc
Stroke: 74mm
Cylinders: Cast Iron.
Pistons: Hypereutectic
Dome CC: 0
Piston Angle: Flat top
Kit includes:4 Cylinders, 4 Pistons, A set of Piston Rings, and 4 wrist pins and clips.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0081180S
008 11 80S
0081180S
The product you are viewing cross references to these numbers
€924.90
Now €832.41
In stock
Vehicle Group
- Porsche 356 1950-55
Information
Cylinder Kit, VW 80mm.
Restore engine performance and reliability with this OE Match Cylinder Kit, VW 80mm. Produced to OE-style specifications, this complete cylinder kit is designed for compatible classic Volkswagen air-cooled engines and is suitable for Porsche applications using the same engine platform where applicable. Manufactured from high-quality cast materials with precision-machined cylinder bores, the kit is engineered to deliver excellent durability, efficient heat dissipation, and consistent sealing. It is ideal for engine rebuilds, maintenance, performance restoration, and classic vehicle refurbishment projects.
Fits:
The cylinder kit forms the combustion chamber walls in conjunction with the pistons and piston rings, providing the sealed environment required for efficient compression and combustion. Over time, continuous piston movement, heat cycles, and normal engine wear can cause the cylinder bores to become worn, tapered, scored, or out of round. Replacing worn cylinders restores engine compression, improves oil control, and helps return the engine to smooth, efficient operation.
What This Product Does:
Symptoms Of Wear Or Failure:
Why Replacement Matters:
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0081180L
The product you are viewing cross references to these numbers
Restore engine performance and reliability with this OE Match Cylinder Kit, VW 80mm. Produced to OE-style specifications, this complete cylinder kit is designed for compatible classic Volkswagen air-cooled engines and is suitable for Porsche applications using the same engine platform where applicable. Manufactured from high-quality cast materials with precision-machined cylinder bores, the kit is engineered to deliver excellent durability, efficient heat dissipation, and consistent sealing. It is ideal for engine rebuilds, maintenance, performance restoration, and classic vehicle refurbishment projects.
Fits:
- Porsche 356 1950-55
The cylinder kit forms the combustion chamber walls in conjunction with the pistons and piston rings, providing the sealed environment required for efficient compression and combustion. Over time, continuous piston movement, heat cycles, and normal engine wear can cause the cylinder bores to become worn, tapered, scored, or out of round. Replacing worn cylinders restores engine compression, improves oil control, and helps return the engine to smooth, efficient operation.
What This Product Does:
- Provides precision-machined cylinder bores for the pistons.
- Restores engine compression and combustion efficiency.
- Supports correct piston and piston ring operation.
- Improves oil control and reduces blow-by.
- Dissipates engine heat effectively.
- Replaces worn, scored, or damaged cylinders.
- Provides an OE-style fit for straightforward engine rebuilding.
Symptoms Of Wear Or Failure:
- Low engine compression.
- Excessive oil consumption.
- Blue exhaust smoke caused by oil burning.
- Loss of engine power or performance.
- Excessive crankcase blow-by.
- Scored, worn, or tapered cylinder bores.
- Piston slap or excessive engine noise.
- Damage identified during engine overhaul.
Why Replacement Matters:
- The cylinders are fundamental to engine performance, providing the precision sealing surfaces required for efficient combustion and reliable piston movement. As cylinder bores wear, compression is reduced, oil consumption increases, and engine performance deteriorates. Continued operation with worn cylinders can accelerate wear of pistons, rings, and other internal engine components.
- Replacing worn cylinders with this OE Match 80mm Cylinder Kit restores compression, improves engine efficiency, reduces oil consumption, and supports long-term engine reliability. Manufactured as a direct replacement and produced to OE-style specifications, this OE Match Cylinder Kit provides reliable fit, performance, and durability for classic Volkswagen and compatible Porsche engine maintenance, repairs, and restoration projects.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0081180L
008 11 80L
0081180L
The product you are viewing cross references to these numbers
€554.92
Now €499.43
Orderable
Vehicle Group
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
Information
Cylinder Kit, Biral VW 82.5mm.
Restore or upgrade your engine with this OE Match Biral VW 82.5mm Cylinder Kit. Produced to OE-style specifications, this premium Biral cylinder kit is designed for compatible classic Volkswagen air-cooled engines and Porsche applications using the same engine platform where applicable. Featuring cast iron cylinder liners bonded to aluminium cooling fins, Biral cylinders combine the excellent wear resistance of cast iron with the superior heat dissipation of aluminium. Manufactured to precise tolerances, the kit delivers outstanding durability, efficient cooling, and consistent engine performance, making it ideal for engine rebuilds, performance upgrades, and concours-quality restoration projects.
Fits:
The cylinder kit forms the combustion chamber walls in conjunction with the pistons and piston rings, providing the precision sealing surfaces required for efficient compression and combustion. The Biral construction offers improved thermal management compared with conventional cast iron cylinders, helping to maintain stable operating temperatures under demanding conditions. Over time, cylinder bores can become worn, tapered, scored, or distorted due to heat and continual piston movement, resulting in reduced compression and increased oil consumption. Replacing worn cylinders restores engine efficiency and long-term reliability.
What This Product Does:
Symptoms Of Wear Or Failure:
Why Replacement Matters:
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0081182BL
The product you are viewing cross references to these numbers
Restore or upgrade your engine with this OE Match Biral VW 82.5mm Cylinder Kit. Produced to OE-style specifications, this premium Biral cylinder kit is designed for compatible classic Volkswagen air-cooled engines and Porsche applications using the same engine platform where applicable. Featuring cast iron cylinder liners bonded to aluminium cooling fins, Biral cylinders combine the excellent wear resistance of cast iron with the superior heat dissipation of aluminium. Manufactured to precise tolerances, the kit delivers outstanding durability, efficient cooling, and consistent engine performance, making it ideal for engine rebuilds, performance upgrades, and concours-quality restoration projects.
Fits:
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
The cylinder kit forms the combustion chamber walls in conjunction with the pistons and piston rings, providing the precision sealing surfaces required for efficient compression and combustion. The Biral construction offers improved thermal management compared with conventional cast iron cylinders, helping to maintain stable operating temperatures under demanding conditions. Over time, cylinder bores can become worn, tapered, scored, or distorted due to heat and continual piston movement, resulting in reduced compression and increased oil consumption. Replacing worn cylinders restores engine efficiency and long-term reliability.
What This Product Does:
- Provides precision-machined cylinder bores for the pistons.
- Restores engine compression and combustion efficiency.
- Combines cast iron wear resistance with aluminium cooling.
- Improves heat dissipation for stable engine temperatures.
- Supports correct piston and piston ring operation.
- Replaces worn, scored, or damaged cylinders.
- Provides an OE-style fit for straightforward engine rebuilding.
Symptoms Of Wear Or Failure:
- Low engine compression.
- Excessive oil consumption.
- Blue exhaust smoke caused by oil burning.
- Loss of engine power or performance.
- Excessive crankcase blow-by.
- Scored, worn, or tapered cylinder bores.
- Piston slap or abnormal engine noise.
- Damage identified during engine overhaul.
Why Replacement Matters:
- The cylinders are fundamental to engine performance, providing the precision-machined surfaces required for effective piston sealing and efficient combustion. As cylinder bores wear, engine compression decreases, oil consumption increases, and overall performance suffers. Biral cylinders offer the additional benefit of superior cooling performance, helping to reduce operating temperatures while maintaining excellent wear characteristics.
- Replacing worn cylinders with this OE Match Biral 82.5mm Cylinder Kit restores engine compression, improves cooling efficiency, reduces oil consumption, and supports long-term engine reliability. Manufactured as a direct replacement and produced to OE-style specifications, this OE Match Biral Cylinder Kit provides reliable fit, performance, and durability for classic Volkswagen and compatible Porsche engine maintenance, performance upgrades, repairs, and restoration projects.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0081182BL
0081182BL
008 11 82BL
The product you are viewing cross references to these numbers
€578.72
Now €520.85
Orderable