do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
Includes clutch arm, cable clevis, slave cylinder, spacer, seals and our billet slave cylinder bracket with bolts. This requires the use of the 1978 and earlier clutch fork pivot shaft.
Note: This requires a portion of the rib on the bottom of the transmission that holds the original clutch cable to be cut away on 72-77 models. To go back to a cable configuration if one so chooses can be done with a bolt on bracket.
A 3/4" clutch master cylinder is recommended - not included.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95011623712
The product you are viewing cross references to these numbers
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
Fits:
Porsche 911 1987-89 with G50/50 Gearbox
Porsche 930 Turbo 3.3L 08/1988-07/1989
Porsche 964 1990-94 with G50/50 Gearbox
Porsche 993 1994-97 with G50/50 Gearbox
A clutch that is engaged/disengaged via hydraulic fluid instead of a cable uses a Clutch Master and Clutch Slave Cylinder. When depressing the clutch pedal a lever is squeezed, forcing hydraulic fluid through hydraulic lines to a "slave cylinder" which houses a piston. The piston forces a push rod to engage or disengage the clutch. A clutch master cylinder that contains the hydraulic fluid sits on a support har near the clutch lever. When either the Master or Slave Cylinder fail the clutch is unable to be disengaged.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95011623712
The product you are viewing cross references to these numbers
- Porsche 911 1987-1989 3.2L G50
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
Clutch slave cylinder. Porsche 911 86>> / 964 / 993
With our clutch slave cylinder for the Porsche 911, the foot force used when clutching is reduced by approx. 30%.
This significantly increases driving comfort, as engaging the clutch is noticeably more comfortable.
The clutch slave cylinder is a hydraulic component, consisting of a cylinder with piston and a movable piston rod. This actuates a mounted arm on the vehicle side, which disconnects or closes the clutch. Since the piston rod does not press centrally on the piston, lateral forces arise in the series cylinder and thus friction between the piston and cylinder. The advantage of the MPL clutch slave cylinder is that these side forces are absorbed by 2 graphite Teflon rings that are guided in grooves in the piston, which means that there is only minimal friction. This structure made it possible to manufacture the housing from weather-resistant aluminium, which also protects against wear thanks to the fine machining of the cylinder and the electrochemical surface treatment. In order to make the actuation even easier and the engagement of the clutch even smoother, the piston surface was slightly enlarged.
The slave cylinder is supplied without the bellows and spring, these must be taken from the original.
Assembly instructions are included in the delivery.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95011623712
The product you are viewing cross references to these numbers
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
Fits:
Porsche 911 1987-89 with G50/50 GearBox
Porsche 964 1990-94 with G50/50 GearBox
Porsche 993 1994-97 with G50/50 GearBox
A clutch that is engaged/disengaged via hydraulic fluid instead of a cable uses a Clutch Master and Clutch Slave Cylinder. When depressing the clutch pedal a lever is squeezed, forcing hydraulic fluid through hydraulic lines to a "slave cylinder" which houses a piston. The piston forces a push rod to engage or disengage the clutch. A clutch master cylinder that contains the hydraulic fluid sits on a support har near the clutch lever. When either the Master or Slave Cylinder fail the clutch is unable to be disengaged.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95011623712
The product you are viewing cross references to these numbers