do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
- Porsche 997 MK1 TURBO 2007-09
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
the boring tool can be purchased or rented from us
Code: 987997IMSTOOL
Fits:
Porsche 997 2005-08
Porsche Boxster 987
Porsche Cayman 987
(Not for M96 Engines)
Porsche Ims Intermediate Shaft Bearing Upgrade - Eternal Fix with Oil Pressure Feed - 62 MM - Closed Engine Permanently Fix Your Intermediate Shaft With The Eternal Fix! Unlike Failure Prone Ball Bearings, Eps Uses A Patented Cylindrical Bearing With Thrust Control.
Prevent future catastrophic engine failure permanently with the only true Eternal Fix for the notorious Porsche intermediate shaft bearing. Unlike the other failure-prone ball bearing products that the original IMS and other upgrades on the market use, EPS uses a patented cylindrical bearing with thrust control that can be pressed directly into the back of the engine without disassembly. The cylindrical bearings have over 12 times the load capacity of other ball bearing solutions making the EPS IMS bearing the clear choice. Backed by a full 5-year warranty and includes an oil feed modification kit. Order yours today!
WHAT MAKES OUR SOLUTION DIFFERENT?
Roller bearings are not intended for carrying large axial loads. Similar to failure-prone ball bearings, when cylindrical roller bearings are used for thrust control, the roller becomes compromised due to the limited surface contact area on the sides of the rollers. The results of using a cylindrical bearing for thrust control will be similar to all other ball bearing solutions.
In our patented system, we use a 15mm cylindrical bearing with thrust control that allows for the separation of the axial load from the radial load. Our roller bearings do NOT carry the axis load (thrust control) on the side, which leaves the roller free to carry only the radial load (main load). The axial load is carried exclusively on the entire permitter of the outer race. This results in a bearing that is not overloaded and will last the lifetime of the engine.
EPS recommends using this product in conjunction to the Rear Main #8 Seal and Housing
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
987997IMS62MM
The product you are viewing cross references to these numbers
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
for M96 Engines and Early M97.01
Fits:
Porsche 996 C2 3.4L 1998 - 2001
Porsche 996 C2 3.6L 2002 - 2004
Porsche 996 C4 3.4L 1999>>
Porsche 996 C4 3.6L 2000>>
Porsche 996 C4 3.4L 2001>>
Porsche 996 C4 3.6L 2002 - 2004
Porsche 996 C4S 3.6L 2002- 2005
Porsche 997 C2 3.6L 2005 M96.05
Porsche 997 C2S 3.8L 2005 M97.01**
Porsche 997 C4 3.6L 2005 M96.05
Porsche 997 C4S 3.8L 2005 M97.01**
**Engine (3.8) number up to M97/01 68509790 has the older IMS bearing (this product fits) and Engine number from M97/01 68509791 has the larger revised IMS. (this product does not fit)
Porsche Boxster 986 2.5L 1997 - 1999
Porsche Boxster 986 2.7L 2000 - 2003
Porsche Boxster 986 2.7L 2004 - 2005
Porsche Boxster S 986 3.2L 2000 - 2005
Porsche Boxster 987 2.7L / 3.2L / 3.4L
**M96 Engine only
Fits engine types: Carrera 996 M96 engines, Boxster 986 M96 Engines, Boxster 987 M96 Engines, Carrera 997 M96 & M97.01 **Engine (3.8) number up to M97/01 68509790 has the older IMS bearing (this product fits) and Engine number from M97/01 68509791 has the larger revised IMS. (this product does not fit)
IMS Eternal Fix retro fit kit installs in-car without removal or disassembly of the engine required. The Cylindrical Bearing with Thrust Control design has a load capacity 5 times greater than the inferior, failure prone, Ball Bearing solutions on the market!
Why Cylindrical is Best?
Cylindrical Bearings have very high load bearing capacity, 5 times more than Ball Bearing. Cylindrical Bearings are used in, High Temp & Low Viscosity Lubrication such as Automatic Transmissions. They can carry extreme lateral pressure without wear to the friction surfaces. This is because the bearing friction surface is flat not concave.
IMS Intermediate Shaft Bearing Upgrade – EPS Eternal Fix (M96 / Early M97.01) Prevent future IMS-related engine damage with the EPS Eternal Fix for the well-known Porsche IMS bearing issue. Unlike common ball-bearing upgrades, EPS uses a patented cylindrical roller bearing with thrust control, engineered to separate axial (thrust) loads from radial (running) loads for long-term durability.
What makes EPS different?
Many bearing upgrades can be compromised when thrust loads act on the bearing rollers. EPS’s patented design ensures the rollers carry radial load only, while the axial load is carried around the full perimeter of the outer race. This reduces overload conditions and delivers a solution engineered to last the life of the engine.
Key benefits
Patented cylindrical bearing with thrust control (not a ball-bearing solution)
In-car installation: designed to be pressed into the rear of the engine without engine disassembly EPS states significantly increased load capacity vs typical ball-bearing upgrades (often quoted as up to 12x)
Backed by an EPS 5-year warranty
Recommended to install alongside the Rear Main (#8) Seal and Housing
Important fitment note (997 3.8L M97.01) Engine numbers up to M97/01 68509790 use the older IMS bearing (fits). Engine number M97/01 68509791 onwards has the larger revised IMS (does not fit). Please verify engine number before ordering.
For More Information CLICK HERE
For Installation Instructions CLICK HERE
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99610590102EPS
The product you are viewing cross references to these numbers
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
Before ordering, it is necessary to identify which bearing size you need. There are two types of bearings (Single row and Double row) used in these engines. This kit comes with SINGLE row bearing.
Fits:
Porsche 986 Boxster 1997 -2004
Porsche 996 Carrera 1997 -2004
Kit Includes:
Patented DOF Flange with anti-rust zinc plating
IMS Bearing
3 micro-encapsulated Porsche bolts
Spacer for bearing
Engine oil port adapter with crush ring
Cam Plug
3,000psi hydraulic hose
Fitting for hose
Thread locker
Installation instructions
The direct oil feed (DOF) solution uses a patent pending custom made Intermediate Shaft Flange that utilizes a direct oil feed to the original Intermediate Shaft Bearing. It uses an adapted pressure fed oil line from a positive oil pressure feed on the cylinder head directly to an opening in the custom Intermediate Shaft Flange. This feeds fresh oil directly to the open end of the IMS bearing (after removing the seal to expose the ball bearings on the IMS bearing). By using a positive oil feed from the engine's cylinder head valve cover, there will always be a consistent flow of oil directed to the open end of the intermediate shaft bearing.
This is a cost effective way to help protect against a possible IMS bearing failure, using the original bearing. The system, however can also be used when replacing the bearing with a new SKF steel ball bearing for added insurance with a new, zero mile bearing.
For Installation Instructions CLICK HERE
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IMSDOF9961
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
Before ordering, it is necessary to identify which bearing size you need. There are two types of bearings (Single row and Double row) used in these engines. This kit comes with DOUBLE row bearing.
Fits:
Porsche 986 Boxster 1997 -2004
Porsche 996 Carrera 1997 -2004
Kit Includes:
Patented DOF Flange with anti-rust zinc plating
IMS Bearing
3 micro-encapsulated Porsche bolts
Spacer for bearing
Engine oil port adapter with crush ring
Cam Plug
3,000psi hydraulic hose
Fitting for hose
Thread locker
Installation instructions
The direct oil feed (DOF) solution uses a patent pending custom made Intermediate Shaft Flange that utilizes a direct oil feed to the original Intermediate Shaft Bearing. It uses an adapted pressure fed oil line from a positive oil pressure feed on the cylinder head directly to an opening in the custom Intermediate Shaft Flange. This feeds fresh oil directly to the open end of the IMS bearing (after removing the seal to expose the ball bearings on the IMS bearing). By using a positive oil feed from the engine's cylinder head valve cover, there will always be a consistent flow of oil directed to the open end of the intermediate shaft bearing.
This is a cost effective way to help protect against a possible IMS bearing failure, using the original bearing. The system, however can also be used when replacing the bearing with a new SKF steel ball bearing for added insurance with a new, zero mile bearing.
For Installation Instructions CLICK HERE
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IMSDOF9962
The product you are viewing cross references to these numbers
This kit is comprised of the following items: