do not press the back button…
Your Vehicle
Porsche // Macan (95B) MK3 2022>> // Any
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 914 (1970-1976)
OE Match rear wheel hub supplied with studs for classic Porsche 911 and 914-6 applications. Check the detailed application notes below, including the 911 RS exclusion.
Fits
- Porsche 911 1969 to 1973 (not RS)
Supplied model classification: 911 & 912 (1965-1989)=>911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F) - Porsche 914-6 1970 to 1972
Supplied model classification: 914 (1970-1976)
The model classifications are broader than the specific application notes; they do not establish compatibility with every listed variant or year. Check fitment for your specific vehicle (model, year, engine) before ordering.
Diagram: 501-00, item 22 (rear axle 911 1970-73). Diagram: 501-05, item 10 (rear axle 911 1969).
What This Product Does
The hub provides the rotating mounting interface for the rear wheel and brake disc, working with the wheel bearing within the rear axle assembly. Its studs provide the fixing points for the wheel nuts. This component is a wheel hub, rather than the surrounding trailing arm or wheel carrier.
Functions
- Provides the rear wheel mounting interface.
- Locates the wheel and brake disc relative to the bearing assembly.
- Transfers driving and braking loads through the wheel connection.
Technical Details
- Part reference: 90133106509.
- Position: Rear.
- Supplied with wheel studs.
- The 1970–73 rear axle diagram identifies the application as 911 T/E/S.
- Both supplied diagrams record two hubs per vehicle; this is not a statement of pack contents.
- Bearings and trailing arms are identified as separate components in the supplied diagrams.
Symptoms of Fault
- Wheel movement associated with a worn bearing seating surface.
- Recurring bearing noise where hub wear has been confirmed.
- Vibration or inconsistent braking feel associated with an untrue mounting face.
- Corrosion affecting the bearing fit or mating surfaces.
Why Replacement Matters
A damaged bearing seat or distorted mounting face may require hub renewal rather than bearing replacement alone. Inspect the bearing, studs and adjoining components before deciding which parts need replacing; noise or vibration does not identify the hub as the cause by itself.
FAQs
When should the hub be renewed with the bearing?
When inspection confirms wear or damage at the bearing seat, or distortion of the mounting face.
Is additional fitting hardware required?
Check the vehicle-specific repair instructions for bearings, seals and fasteners required for the work. Do not assume they are included with the hub.
What matters during installation?
Clean the mating surfaces and use suitable pressing and support tools to avoid damaging the hub or bearing.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90133106509
The product you are viewing cross references to these numbers
for Porsche Boxster / Cayman / 911 / Panamera / Taycan
Sold each.
Fits:
Porsche 911 (993 / 996 / 997 / 991 / 992)
Porsche Boxster (986 / 987 / 981)
Porsche Cayman (987 / 981 / 718)
Porsche Panamera (970)
Porsche Taycan
Alignment eccentric washer, also referred to as a cam adjust arm or control arm adjust cam, is used in the rear suspension of certain Porsche 911, Boxster, Cayman and Panamera models.
Position on Vehicle: Rear suspension — at the rear control arm or track rod mounting point, typically used to adjust alignment of the wheel carrier, track bar or control arm.
Applications: Ideal for when original eccentric bolts or washers are worn, alignment cannot be set correctly, or when replacing control arms/track rods and correct alignment geometry is required.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
PAF007648
The product you are viewing cross references to these numbers
Cleaning kit for corroded wheel studs & adjacent hub surfaces
Removes dirt & corrosion & prepares surfaces for correct torque application
Ideal for preparing wheels, hubs and brake discs or drums for re-assembly
Suitable for use with power drill or air impact wrench
Kit contains:
- Stud cleaner body including velcro pad
- Replacement velcro pads x 2
- Fine cleaning discs x 5
- Coarse cleaning discs x 5
Find out about Textar product verification here
Aluminium bell with steel core and 12,5 mm (1/2“) seat for use on pneumatic impact screwdrivers.
Corrosion between the rim and the wheel hub is removed so torque values can no longer be distorted.
Complete with 1 cleaning disc
Find out about Textar product verification here