Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
TDC indicators for Porsche 911 - SR02
SR02
Vehicle Group
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Information
TDC indicators for Porsche 911
To ensure the utmost in timing precision, the true TDC of all engines should be checked to confirm the accuracy of the pulley TDC mark in relation to the real TDC. This tool screws into the spark plug hole and gives a mechanical indication of where the piston is in relation to the pulley/crankshaft. By rotating the crankshaft and touching/bumping the piston against the dead stop BTDC, and then rotating the engine in the opposite direction and touching/bumping the piston again against the dead stop ATDC, recording both measurements on a degree wheel, the pulley, or our DigiDix- SR095, you can calculate pure TDC.
Available for either 12mm or 14mm spark plug holes.
Sold separately.
To ensure the utmost in timing precision, the true TDC of all engines should be checked to confirm the accuracy of the pulley TDC mark in relation to the real TDC. This tool screws into the spark plug hole and gives a mechanical indication of where the piston is in relation to the pulley/crankshaft. By rotating the crankshaft and touching/bumping the piston against the dead stop BTDC, and then rotating the engine in the opposite direction and touching/bumping the piston again against the dead stop ATDC, recording both measurements on a degree wheel, the pulley, or our DigiDix- SR095, you can calculate pure TDC.
Available for either 12mm or 14mm spark plug holes.
Sold separately.
Prices from: €165.01
Related products
Information
Mounting bolt kit for engine & gearbox stand
Finally an elegant way to secure your engine to the engine yoke. No need for sockets, washers, and oversized nuts to take up slack. Use these knurled nuts and adapters to mount the different length case studs to the yoke. These adapters allow clearance for mounting the clutch. Hard-coated aluminum and stainless steel for years of service.
Finally an elegant way to secure your engine to the engine yoke. No need for sockets, washers, and oversized nuts to take up slack. Use these knurled nuts and adapters to mount the different length case studs to the yoke. These adapters allow clearance for mounting the clutch. Hard-coated aluminum and stainless steel for years of service.
Price: €77.12
In stock
Information
Connector removal tool - for VAG, Porsche
For the removal of VAG & Porsche push and pull connectors.
• For the removal of VAG and Porsche connectors.
• Connectors are found on MAF sensors, coil packs, headlights, fog lights, level sensors, map sensors etc.
• Fits directly onto the push and pull connectors.
• Black plastic handle for easy grip.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
6547
The product you are viewing cross references to these numbers
For the removal of VAG & Porsche push and pull connectors.
• For the removal of VAG and Porsche connectors.
• Connectors are found on MAF sensors, coil packs, headlights, fog lights, level sensors, map sensors etc.
• Fits directly onto the push and pull connectors.
• Black plastic handle for easy grip.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
6547
6547
The product you are viewing cross references to these numbers
Price: €45.08
In stock
Information
Connector removal tool long series - for VAG/Porsche
For the removal of VAG and Porsche connectors found on MAF sensors, coil packs, headlights, fog lights, level sensors, map sensors etc.
• Fits directly on to the push and pull connectors and opens the locking tabs as pressure is applied.
• Applications include MAF sensors, coil packs, MAP sensors, CPS sensors and light connectors.
• Soft grip T-handle.
• 20mm offset head, 160mm long. EU Registered Design.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
7859
The product you are viewing cross references to these numbers
For the removal of VAG and Porsche connectors found on MAF sensors, coil packs, headlights, fog lights, level sensors, map sensors etc.
• Fits directly on to the push and pull connectors and opens the locking tabs as pressure is applied.
• Applications include MAF sensors, coil packs, MAP sensors, CPS sensors and light connectors.
• Soft grip T-handle.
• 20mm offset head, 160mm long. EU Registered Design.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
7859
7859
The product you are viewing cross references to these numbers
Price: €22.96
In stock