do not press the back button…
Your Vehicle
Porsche // 964 (911) (1989-1994) // 964 (911) RS 3.8L 1991-93
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 356B 1959-63
This black OE Match rear torsion bar cover is intended for the torsion-bar and spring-plate assembly fitted to applicable Porsche 356 models. Its open-centre design accommodates the round outer bushing and provides access to the end of the torsion-bar assembly.
Fits
Porsche 356 1950–65
Porsche 356A 1955–59
Porsche 356 B T5 1.6L 12/1959–08/1961
Porsche 356B / 356C 1960–65, where the open cover is specified
Check fitment for your specific vehicle (model, year, engine) before ordering.
What This Product Does
The cover fits to the rear axle housing around the spring plate and outer torsion-bar bushing. It helps retain the bushing in its working position while shielding the surrounding mounting area from road dirt and moisture. Correct installation supports consistent spring-plate location and suspension geometry.
Functions
- Secures the outer round bushing at the rear spring plate.
- Covers the torsion-bar housing and adjacent mounting area.
- Provides centre access through the open cover design.
- Supports correct spring-plate positioning.
- Fits either the left or right side of the rear axle assembly.
Technical Details
- Component type: rear torsion-bar or spring-plate cover.
- Configuration: open cover with centre hole.
- Finish colour: black.
- Bushing profile: round.
- Installation position: rear axle, left or right.
- Vehicle quantity: two covers are shown in the relevant factory assembly diagrams.
Symptoms of Fault
- Corrosion, cracking or distortion around the cover.
- Movement at the spring plate or outer bushing.
- Knocking or clunking from the rear suspension over uneven surfaces.
- Perished, compressed or displaced supporting rubber.
- Difficulty maintaining the intended rear ride height or alignment.
- Damaged or seized mounting hardware around the cover plate.
Why Replacement Matters
A damaged or heavily corroded cover may no longer locate the outer bushing correctly. Renewal during a rear suspension overhaul helps restore the assembly and prevents a worn cover from being refitted with new bushes or related hardware. Inspect the spring plate, bushing, torsion bar and fasteners at the same time, as noise or movement may involve more than one component. Alignment and ride height should be checked after substantial torsion-bar or spring-plate work.
OE Reference
- 64433315101
- 8152250900
- 113511227B
- 511201002OE
FAQs
- Is this an open or closed cover?
This is the open version, manufactured with a centre hole. - Can it be installed on either side?
Yes. The cover is specified for left- or right-hand rear installation, with two used on the vehicle. - Should the bushing be inspected during replacement?
Yes. Check the round outer bushing, spring plate and mounting hardware for wear, corrosion or damage before assembly. - Is alignment required afterwards?
An alignment and ride-height check is advisable if the spring plate, torsion bar or its adjustment has been disturbed.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
64433315101
The product you are viewing cross references to these numbers
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
Fits:
Porsche 964 1989-94
Click 'Zoom in' for large parts diagram.
Diagram ref no 4
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
96450335100GRV
The product you are viewing cross references to these numbers