前侧车顶支架


- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
一套 4 件。
#罗勒#

适合:
保时捷 996 C2 / C2S
原厂橡胶衬套支架的终极替代品。兼容原厂和售后市场的前减震器。
安装孔允许超过 1 度的额外负外倾角。
采用 CNC 加工的 6061 黑色阳极氧化铝结构,配有不锈钢硬件。
减少急转弯时前轮和后轮外倾角的变化,以保持最佳轮胎接触,从而提高牵引力。
请注意:作为一种选择,您可以添加橡胶靴保护器(在篮子阶段)以密封轴承,防止任何道路污垢和碎片。
图库图片所示,但不包含在顶部支架价格中。按件出售。需4个。
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
360250996KIT
您正在查看的产品与这些编号存在交叉引用关系
该套件包括以下商品:





- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
4 套升降垫片(2 x ft / 2 x Rr)

適用於:
保时捷 996 Carrera 2 - 1997 年 - 2005 年
保时捷 996 Carrera 4 - 1997 年至 2005 年
保时捷 996 C4S / 涡轮增压 - 1997 年至 2005 年
适用于保时捷 996 的 2 英寸升降套件及副车架下降套件
推出 996 螺栓固定升降套件,与 C2、C4 和 Turbo 底盘兼容。该套件直接安装在支柱顶部,与我们的副车架下降系统配合使用,可提供约 2 英寸的额外升力。此增强功能可提高离地间隙,同时保持车辆的原始行驶质量。
该套件经过精心设计,可与 OEM 支柱和售后市场绞牙避震无缝配合。前上部支架设计为两件式系统,以便在必要时进行外倾角调整。此外,虽然 OEM 支柱塔允许进行微小调整,但我们的支架经过专门设计,可在需要时增加负外倾角。
副车架下降套件
举升 996 底盘时,轮胎较高所需的额外高度将增加车轴几何形状。增加副车架下沉将提高车轴性能和使用寿命。它还将允许更多的悬架行程并重新定位控制臂以获得更好的几何形状。
专为保时捷 996 Overland/Safari 项目设计。
垫片由 6061 铝坯 CNC 加工而成,然后进行灰色阳极氧化以进行保护。
硬件为 10.9-12.9 定制版。无通用螺纹杆。所有部件均镀锌,具有终身防腐蚀性能。
套件包含:
2 x 前升降垫片
2 x 后升降垫片
18 x 副车架垫片(4 种尺寸)
安装硬件
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
EWOR996LK50MMKIT
您正在查看的产品与这些编号存在交叉引用关系
该套件包括以下商品:





- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005

在极端条件下,例如公路赛和越野赛,需要负外倾角来尽可能多地保持轮胎与路面的接触面。原厂悬挂支架无法让您达到此类性能驾驶所需的负外倾角。Rennline 的密封外倾板结合了 FK 赛车球面轴承,消除了与工厂橡胶支架相关的模糊反馈。
适合
保时捷 996 Carrera 2(两轮驱动)
注意:使用工厂不可调节支柱和工厂弹簧座时,必须拆除防风雨密封条
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
SUSPENSIONKIT08
您正在查看的产品与这些编号存在交叉引用关系
该套件包括以下商品:





- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12


Fits:
Porsche 996 C2
Porsche 986 Boxster
Porsche 997 C2
Porsche 987 Boxster
Porsche 987 Cayman
Ultimate replacement for factory rubber bush mount. Compatible with OE and aftermarket struts.
Mounting holes allow for more than 1 deg of extra negative camber.
CNC machined 6061 black anodized aluminum construction with stainless steel hardware.
Reduces front wheel camber changes during hard cornering to maintain optimum tire contact for improved traction.
Please note: As an option, you can add rubber boot protectors (at the basket stage) to seal the bearing from any road grime and debris.
Shown on the picture in the gallery but not included in the price of the top mounts. Sold as each. 2 required.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
360250996F
您正在查看的产品与这些编号存在交叉引用关系





- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
4 套升降垫片(2 x ft / 2 x Rr)

適用於:
保时捷 996 Carrera 2 - 1997 年 - 2005 年
保时捷 996 Carrera 4 - 1997 年至 2005 年
保时捷 996 C4S / 涡轮增压 - 1997 年至 2005 年
适用于保时捷 996 的 2 英寸升降套件。
推出 996 螺栓固定升降套件,与 C2、C4 和 Turbo 底盘兼容。该套件直接安装在支柱顶部,与我们的副车架下降系统配合使用,可提供约 2 英寸的额外升力。此增强功能可提高离地间隙,同时保持车辆的原始行驶质量。
该套件经过精心设计,可与 OEM 支柱和售后市场绞牙避震无缝配合。前上部支架设计为两件式系统,以便在必要时进行外倾角调整。此外,虽然 OEM 支柱塔允许进行微小调整,但我们的支架经过专门设计,可在需要时增加负外倾角。
套件包含:
2 x 前升降垫片
2 x 后升降垫片
安装硬件
可选套件:
副车架下降套件 - 需要适当的轴间隙和增加的悬架行程。
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
EWOR996LK50MM-2
您正在查看的产品与这些编号存在交叉引用关系





- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 GT3 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche 914 (1970-1976)
Sold per kit, 1 kit req'd per car.


Porsche 996 / 997 C2 models 1999-2012
Porsche 986 / 987 1997-12
Elephant Racing's QuickChange™ Camber plates offer true ease of adjustment. The "slider" design allows a full range of adjustment without the need for removing and rotating the plate for C2, C4, and Turbo models.
More Camber
Range of adjustment is extreme, with 19mm of added travel. This delivers over 2 degrees of added camber, allowing even DOT-R tires and slicks to produce maximum grip.
QuickChange Camber Plate for C4 and Turbo Models
The Quickchange camber plates are available for C2, C4 and Turbo models and work with stock-type springs and coilovers. They will not raise ride height when used with stock-type springs.
Higher Performance
Spherical bearings further improve performance. The spherical bearings pivot freely, but eliminate the deflection that is inherent with the factory rubber bushings. This is important for two reasons;
– The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.
– The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.
Fully Weather Sealed
The included spherical bearings are oversized, maintenance-free, and PTFE lined – they never need lubrication.
Integrated weather seals on both bottom and top of the spherical bearing extend bearing life. Dirt and water enter competing non-sealed products to accelerate bearing wear. Worse yet are bottom-only seals that can actually trap water that enters the open bearing top!
Our weather seals are fully compatible with coilovers and stock type springs.
Use Stock Springs or Coilovers
Fully compatible with stock springs and aftermarket lowering springs. Also supports coilovers that use and upper spring perch.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2152205
您正在查看的产品与这些编号存在交叉引用关系





- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
2 件套

适合
保时捷 996 C2 3.4L / 3.6L 1998-2005 年(两轮驱动)
保时捷 986 Boxster 1997-04
在极端条件下,例如公路赛和自动越野赛,需要负外倾角来尽可能多地保持轮胎与路面的接触面。原厂悬挂支架无法让您达到这种性能驾驶所需的负外倾角。Rennline 的密封外倾板结合了 FK 赛车球面轴承,消除了与工厂橡胶支架相关的模糊反馈。一套两个。为什么 Rennline 的支柱支架是最好的?
* 由于采用集成的工厂 GT3 防风雨密封件,轴承寿命大大增加。
* FK Motorsport 特氟龙内衬球形轴承。
* 刚性轴承支架,不像某些现有产品那样被夹住。
* 经过特殊加工的上螺母,以提供最大负外倾角设置的间隙。
* 允许增加最多 1.25 度的负外倾角。
* 包含特殊工具,用于在拧紧上螺母时防止支柱轴转动。
* 可与所有工厂和售后支柱一起使用,包括工厂不可调节装置。
* 网状机加工底座,重量轻且强度高。
* 完全可重建
* 采用 CNC 加工的 6061 阳极氧化铝结构,配备不锈钢硬件。
注意:使用工厂不可调节支柱和工厂弹簧座时,必须拆除防风雨密封条
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
S20
您正在查看的产品与这些编号存在交叉引用关系





- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
1 kit required per axle

Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster - Front and Rear
Porsche 987 Cayman - Front and Rear
Porsche 996 - Front Only
Porsche 997 - Front Only
Cartridges install easily to replace rubber bushings for 996/997/Boxster/Cayman. An excellent alternative to our QuickChange Camber Plates for cars that don't need more camber but still want the handling precision of a spherical bearing monoball. Spherical bearings improve performance. The spherical bearings pivot freely, but eliminate the deflection that is inherent with the factory rubber bushings.
Eliminating Deflection Is Important For Two Reasons
• The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.
• The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2011002
您正在查看的产品与这些编号存在交叉引用关系



使用高性能顶部支架增强您的保时捷悬架:技术规格和优势
高性能悬挂顶部支架的技术规格:
- 性能悬架上支座(也称为支柱支座或轴承板)是将悬架支柱连接到保时捷底盘的部件。
- 它们通常由铝合金或增强橡胶等高质量材料制成。
- 与标准支架相比,性能顶部支架具有更坚固的结构和改进的设计,从而提供了增强的性能和耐用性。
- 它们具有多种设计和选项,以适合不同的保时捷车型和悬架设置。
- 性能悬架上支架可作为保时捷车辆的售后升级或标准替换件。
升级或更换保时捷性能悬架顶部支架的好处:
改善操纵性和稳定性:性能顶部支架提供更高的刚度和精度,增强车辆在转弯和高速操纵时的操纵特性和整体稳定性。
增强的悬架反馈:升级到性能支架可改善悬架反馈,使驾驶员能够更好地感知和响应道路状况,从而带来更具吸引力的驾驶体验。
降低噪音、振动和声振粗糙度 (NVH):更坚固的顶部支架有助于最大限度地减少传输到底盘的不必要的振动和噪音,从而带来更平稳、更舒适的乘坐体验。
增强的悬架几何结构:性能顶部支架可进行精确的校准调整,优化悬架几何结构,从而改善轮胎磨损、牵引力和转弯性能。
提高耐用性:性能顶部支架旨在承受更高的负载,与标准支架相比,耐用性更高,即使在苛刻的驾驶条件下也能确保长使用寿命。
在 Design911,我们专门为您的保时捷提供合适的零件和专业建议。我们提供专为保时捷车型设计的各种高性能悬架上支架,包括售后升级和 OEM 更换。我们知识渊博的团队可以根据您的保时捷车型、年份和特定的悬架要求帮助您选择合适的上支架。我们了解在性能和舒适性之间找到适当平衡的重要性,我们可以指导您选择最适合您需求的最佳上支架。凭借我们的专业知识和对客户满意度的承诺,我们可以帮助您提升保时捷的悬架性能、操控性和整体驾驶体验。立即联系我们,享受我们的全面支持并获得根据您的要求量身定制的高质量零件。