Please wait… 
Please wait while we process your order,
do not press the back button…
do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Category Filter
Ignition kit with 3 pin Gen 6 CDI module. Porsche 911 2.0ltr / 2.2ltr - IGNITIONKIT9E
IGNITIONKIT9E
Vehicle Group
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
Information
Ignition kit with 3 pin Gen 6 CDI (HKZ) module. Porsche 911 2.0ltr and 2.2Ltr
Fits
Porsche 911 2.0ltr 1965 - 1969
Porsche 911 2.2ltr 1970 - 1972
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
3 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil
The Gen 6 Premium Perma-Tune CDI module makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights.
These LED lights assist in diagnosing both the ignition module and the car. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light which is especially useful for detecting engine misfire.
The LED function lights are mounted in the harness electrical connector and can only be seen with a mirror while the module is powered up.
As an additional feature of the Perma-Tune Premium module, there are three self-resetting overload protectors that protect your Perma-Tune and your car from overload damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part.
Distributor with Harness
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear. Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor, for the 2.0 L and 2.2 L engine. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation.
Simply mount the ignition module to the relay panel where the later model cars had the module mounted and then plug the distributor harness connector into the Perma-Tune module. The power, ground, tachometer and coil connections are made at the existing coil wires. The harness has loop connections that allow joining the wires without having to cut and splice the car harness wires. The Perma-Tune distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look.
The Perma-Tune Bespoke Porsche distributor is an exact fit replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction. Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor. The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance or retard vacuum functions. It just doesn't get any easier than this.
Ignition Coil
The Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a vintage car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKIT9E
The product you are viewing cross references to these numbers
Fits
Porsche 911 2.0ltr 1965 - 1969
Porsche 911 2.2ltr 1970 - 1972
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
3 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil
The Gen 6 Premium Perma-Tune CDI module makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights.
These LED lights assist in diagnosing both the ignition module and the car. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light which is especially useful for detecting engine misfire.
The LED function lights are mounted in the harness electrical connector and can only be seen with a mirror while the module is powered up.
As an additional feature of the Perma-Tune Premium module, there are three self-resetting overload protectors that protect your Perma-Tune and your car from overload damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part.
Distributor with Harness
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear. Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor, for the 2.0 L and 2.2 L engine. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation.
Simply mount the ignition module to the relay panel where the later model cars had the module mounted and then plug the distributor harness connector into the Perma-Tune module. The power, ground, tachometer and coil connections are made at the existing coil wires. The harness has loop connections that allow joining the wires without having to cut and splice the car harness wires. The Perma-Tune distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look.
The Perma-Tune Bespoke Porsche distributor is an exact fit replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction. Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor. The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance or retard vacuum functions. It just doesn't get any easier than this.
Ignition Coil
The Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a vintage car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKIT9E
91160270700
90160250200
911602021
90160250200
The product you are viewing cross references to these numbers
About kit
This kit is comprised of the following items:
1 x 3 Pin CDI ignition module. Porsche 911 / 914/6 1965-77 premium version (91160270700/3
1 x Distributor and harness for Porsche 911 2.0 / 2.2ltr and 914/6 1968-1972 (911602021/3
1 x Ignition coil Porsche 911 1969-83 & 930 1975-89 PermaTune (PCG602502A/3
£1,180.95
Now £1,074.75
Arriving soon
Related products
Vehicle Group
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
Information
Belt and Pin or Twin IGN Distributor.
A design fault on engines up to August 1993 that you MUST fix if not already done so is to add ventilation to the distributor to prevent ozone perishing the distributor drive belt. If this breaks you will be running on one plug per cylinder and will end up with poor performance and possible damage.
The solutions is to also fit a Venting kit.
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
DISTKIT964
The product you are viewing cross references to these numbers
A design fault on engines up to August 1993 that you MUST fix if not already done so is to add ventilation to the distributor to prevent ozone perishing the distributor drive belt. If this breaks you will be running on one plug per cylinder and will end up with poor performance and possible damage.
The solutions is to also fit a Venting kit.
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
DISTKIT964
93060213400
93060292200
The product you are viewing cross references to these numbers
About kit
This kit is comprised of the following items:
1 x Pin for distributor gear (93060292200
1 x DISTRIBUTOR DRIVE BELT (93060213400/1
£20.68
Now £18.61
In stock
Vehicle Group
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
Information
Distributor Vent Kit.
964 Ventilation Kit includes:
- Distributor ventilation connection (A)
- Rubber Grommet (B)
- White Grommet connector (C)
- Hose (D)
HOW TO FIT: Firstly prise of the oval plate arrowed on the distributor with a screwdriver. Then remove the large black air guide pipe as we need to drill a hole in it at the green dot. The pipe removes by loosening jubilee clips at top and bottom. You will also need to remove two sensor connectors on the pipe. I also removed the two sensors near the distributor so that I had easy access to the plate. Drill at 18mm hole in the pipe, 40mm to the right of the tail light ventilation nipple. Deburr the hole and remove all shavings. Install the rubber grommet (B) into the hole and install the white connector (C) into the grommet.Install the distributor connector (A) into the hole in the distributor where the plate was. Finally refit the air pipe and connect back up all the sensors. Install the hose (D) onto the new distributor and air pipe nipples and route
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
00004320252
The product you are viewing cross references to these numbers
964 Ventilation Kit includes:
- Distributor ventilation connection (A)
- Rubber Grommet (B)
- White Grommet connector (C)
- Hose (D)
HOW TO FIT: Firstly prise of the oval plate arrowed on the distributor with a screwdriver. Then remove the large black air guide pipe as we need to drill a hole in it at the green dot. The pipe removes by loosening jubilee clips at top and bottom. You will also need to remove two sensor connectors on the pipe. I also removed the two sensors near the distributor so that I had easy access to the plate. Drill at 18mm hole in the pipe, 40mm to the right of the tail light ventilation nipple. Deburr the hole and remove all shavings. Install the rubber grommet (B) into the hole and install the white connector (C) into the grommet.Install the distributor connector (A) into the hole in the distributor where the plate was. Finally refit the air pipe and connect back up all the sensors. Install the hose (D) onto the new distributor and air pipe nipples and route
Fits:
Porsche 964 1990-94
Porsche 993 1995-97
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
00004320252
00004320252
The product you are viewing cross references to these numbers
£34.30
Now £30.87
In stock
Vehicle Group
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
Information
Distributor o-ring.
Fits:
Porsche 911 1970-89
Porsche 911 (930) Turbo 1975-89
Porsche 964 1989-94 all models
Porsche 993 1995-98 all models
Click 'Zoom in' for large parts diagram.
Diagram ref no 4
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160210201
The product you are viewing cross references to these numbers
Fits:
Porsche 911 1970-89
Porsche 911 (930) Turbo 1975-89
Porsche 964 1989-94 all models
Porsche 993 1995-98 all models
Click 'Zoom in' for large parts diagram.
Diagram ref no 4
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160210201
91160210201
The product you are viewing cross references to these numbers
£3.51
Now £3.16
In stock