do not press the back button…
Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
also known are Engine Crankshaft Position Sensor
The engine crankshaft position sensor (CPS) is a critical component that monitors the crankshaft’s position and rotational speed. It sends this data to the engine control unit (ECU), allowing precise control of fuel injection, ignition timing, and other key engine functions. Without accurate input from the CPS, the ECU cannot properly synchronize spark or fuel delivery—leading to poor performance or even a no-start condition.
Crankshaft sensors typically use magnetic or Hall-effect technology:
Magnetic sensors generate a signal with a coil and magnet as the crankshaft rotates.
Hall-effect sensors detect changes in the magnetic field using a semiconductor for highly accurate readings.
Depending on the engine design, the CPS is usually located near the crankshaft pulley, harmonic balancer, flywheel, or transmission. It reads notches or teeth on a tone wheel to create a signal the ECU can interpret.
Over time, heat, vibration, and contaminants (oil, dirt, or metal shavings) can cause the sensor to fail. When this happens, common symptoms include engine stalling, rough idling, misfires, or a no-start condition.
Fits:- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
Common Symptoms of a Failing Crankshaft Position Sensor
· No Start Condition – If the ECU doesn’t receive a proper signal, the engine won’t start.
· Stalling When Warm – The sensor may fail when the engine reaches operating temperature, causing unexpected stalling.
· Erratic or Dead Tachometer – In some vehicles, a faulty CPS can cause the tachometer to behave irregularly.
· Check Engine Code P0335 – A failed internal circuit may trigger this code, though not always.
· Poor Performance at Certain RPMs – Timing issues can cause hesitation, especially at idle or higher RPMs.
· Multiple Cylinder Misfires – Unlike a single bad coil or injector, CPS failure can cause misfires across all cylinders.
This crankshaft sensor is designed for Porsche 911 G models produced between 1984 and 1989. It serves as a pulse generator, transmitting engine speed data to the DME, and is a frequent culprit when the engine experiences irregular performance.
Identified by the Bosch number ending in 005, this sensor was installed in pairs within the vehicle. A reliable and precise pulse generator is crucial for optimal engine electronics performance.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160621502
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits:
Porsche 911 1987-89 3.2ltr
Porsche 911 Turbo 1989
G50 Gearbox type
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160691001
The product you are viewing cross references to these numbers
Electrical plug housing - multiple applications (see below).
Porsche 986 Boxster 1997-04
- Camshaft position sensor
- Throttle valve
- Ignition coil
Porsche 996 Carrera & GT3 1998-05
- Ignition coil
Porsche 964/993 Carrera & Turbo 1994-98
- Crankshaft position sensor
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99965291640
The product you are viewing cross references to these numbers
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988
- Porsche 968 3.0L 1992-94
- Porsche 968 Sport 3.0L 1994-95
- Porsche 968 CS 3.0L 1993-95
- Porsche 968 Turbo S 3.0L 1993-94
- Porsche 928 4.5L 1978-82
- Porsche 928S 4.7L 1981-83
- Porsche 928S2 4.7L 1984-86
- Porsche 928S4 5.0L 1987-92
- Porsche 928GT 5.0L 1989-91
- Porsche 928GTS 5.4L 1992-95
Fits:
Porsche 928
Porsche 924S
Porsche 944
Porsche 968
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94460611500
The product you are viewing cross references to these numbers