OE Match
OE Match is a brand that provides a wide range of Porsche components, from gaskets to suspension hardware, engine parts, and interior trim. Over 6,700 individual part numbers, and over 11,800 OE cross-references catalogued, and are constantly developing new lines.
OE Match has over 100 new products currently in the engineering phase, which will be quality-controlled and added to their catalog. The mission is to keep all Porsche vehicles on the road by offering a vast selection of parts that can address various problems across different Porsche generations.
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
Kit includes 2 x Lambda oxygen sensor - can be used in any position, before and after catalytic converter
Fits
Porsche 986 Boxster - 1997 to 2002
Porsche 986 Boxster S - 1997 to 2002
Function:
The Oxygen Sensor (also known as Lambda Sensor) is located in the exhaust manifold and measures the amount of unburned oxygen in your engine's exhaust. Based on the amount of oxygen, it sends a signal to your engine computer which then adjusts the air/fuel mixture for optimum engine performance and emission control.
Failure Symptoms:
Excessive fuel consumption, a faulty oxygen sensor can waste 30% of your fuel.
Drivability problems, such as engine surging or hesitation.
High hydrocarbon emissions, failing an emissions inspection.
The engine warning light may be on or service flag displayed.
The ecu/computer stores a mixture-related fault code.
When the oxygen sensor has stopped functioning completely, the catalytic converter may overheat and fail
Maintenance/Service:
Test and/or replace every 30,000 miles.
Perform periodic emission checks.
Watch for service light.
Vehicle manufacturers recommend periodic inspection and replacement of oxygen sensor.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
LAMBDAKIT10
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
Kit includes 4 x Lambda oxygen sensor (before and after catalytic converter)
Fits
Porsche 986 Boxster - 1997 to 2002
Porsche 986 Boxster S - 1997 to 2002
Function:
The Oxygen Sensor (also known as Lambda Sensor) is located in the exhaust manifold and measures the amount of unburned oxygen in your engine's exhaust. Based on the amount of oxygen, it sends a signal to your engine computer which then adjusts the air/fuel mixture for optimum engine performance and emission control.
Failure Symptoms:
Excessive fuel consumption, a faulty oxygen sensor can waste 30% of your fuel.
Drivability problems, such as engine surging or hesitation.
High hydrocarbon emissions, failing an emissions inspection.
The engine warning light may be on or service flag displayed.
The ecu/computer stores a mixture-related fault code.
When the oxygen sensor has stopped functioning completely, the catalytic converter may overheat and fail
Maintenance/Service:
Test and/or replace every 30,000 miles.
Perform periodic emission checks.
Watch for service light.
Vehicle manufacturers recommend periodic inspection and replacement of oxygen sensor.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
LAMBDAKIT8
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
.jpg?width=197 "Lambda oxygen sensor kit after catalytic converter. Porsche 996 / 997 / GT3 - 99660617801, 99660617802, 99660617800 - EX.029.014")
.jpg){kind=link}
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
Kit includes 2 x Lambda Oxygen Sensors (after catalytic converter)
Fits:
Porsche 996 Carrera 2 / Carrera 4 - 2002 to 2005
*Cars with M661 stricter emission control concept
Porsche 996 GT3 MKII 2004 to 2005
Porsche 997.1 Carrera 2 / Carrera 4 - 2005
Porsche 997.1 Carrera 2S / Carrera 4S - 2005
Function:
The Oxygen Sensor (also known as Lambda Sensor) is located in the exhaust manifold and measures the amount of unburned oxygen in your engine's exhaust. Based on the amount of oxygen, it sends a signal to your engine computer which then adjusts the air/fuel mixture for optimum engine performance and emission control.
Failure Symptoms:
Excessive fuel consumption, a faulty oxygen sensor can waste 30% of your fuel.
Drivability problems, such as engine surging or hesitation.
High hydrocarbon emissions, failing an emissions inspection.
The engine warning light may be on or service flag displayed.
The ecu/computer stores a mixture-related fault code.
When the oxygen sensor has stopped functioning completely, the catalytic converter may overheat and fail
Maintenance/Service:
Test and/or replace every 30,000 miles.
Perform periodic emission checks.
Watch for service light.
Vehicle manufacturers recommend periodic inspection and replacement of oxygen sensor.
Diagram ref no 30
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
LAMBDAKIT5
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
Kit includes 2 x Lambda Oxygen Sensors (before catalytic converter)
Fits:
Porsche 996 Carrera 2 / Carrera 4 - 2002 to 2005
*Cars with M661 stricter emission control concept
Porsche 996 GT3 MKII - 2004 to 2005
Porsche 997.1 Carrera 2 / Carrera 4 - 2005
Porsche 997.1 Carrera 2S / Carrera 4S - 2005
Function:
The Oxygen Sensor (also known as Lambda Sensor) is located in the exhaust manifold and measures the amount of unburned oxygen in your engine's exhaust. Based on the amount of oxygen, it sends a signal to your engine computer which then adjusts the air/fuel mixture for optimum engine performance and emission control.
Excessive fuel consumption, a faulty oxygen sensor can waste 30% of your fuel.
Drivability problems, such as engine surging or hesitation.
High hydrocarbon emissions, failing an emissions inspection.
The engine warning light may be on or service flag displayed.
The ecu/computer stores a mixture-related fault code.
When the oxygen sensor has stopped functioning completely, the catalytic converter may overheat and fail
Maintenance/Service:
Test and/or replace every 30,000 miles.
Perform periodic emission checks.
Watch for service light.
Vehicle manufacturers recommend periodic inspection and replacement of oxygen sensor.
Diagram ref no 31
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
LAMBDAKIT4
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 MK1 Carrera 2 3.6L 2005-08
- Porsche 997 MK1 Carrera 2S 3.8L 2005-08
- Porsche 997 MK1 Carrera 4 3.6L 2005-08
- Porsche 997 MK1 Carrera 4S 3.8L 2005-08
Kit includes 4 x Lambda Oxygen Sensors (2 x before and 2 x after catalytic converter)
Fits:
Porsche 996 Carrera 2 / Carrera 4 - 2002 to 2005
*Cars with M661 stricter emission control concept
Porsche 996 GT3 MKII - 2004 to 2005
Porsche 997.1 Carrera 2 / Carrera 4 - 2005
Porsche 997.1 Carrera 2S / Carrera 4S - 2005
Function:
The Oxygen Sensor (also known as Lambda Sensor) is located in the exhaust manifold and measures the amount of unburned oxygen in your engine's exhaust. Based on the amount of oxygen, it sends a signal to your engine computer which then adjusts the air/fuel mixture for optimum engine performance and emission control.
Excessive fuel consumption, a faulty oxygen sensor can waste 30% of your fuel.
Drivability problems, such as engine surging or hesitation.
High hydrocarbon emissions, failing an emissions inspection.
The engine warning light may be on or service flag displayed.
The ecu/computer stores a mixture-related fault code.
When the oxygen sensor has stopped functioning completely, the catalytic converter may overheat and fail
Maintenance/Service:
Test and/or replace every 30,000 miles.
Perform periodic emission checks.
Watch for service light.
Vehicle manufacturers recommend periodic inspection and replacement of oxygen sensor.
Diagram ref no 30 and 31
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
LAMBDAKIT2
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 914 (1970-1976)
Sold each - 2 required per car
Fits:
Porsche 914 - 1970 to 1976
Diagram ref no 5
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
021109339
The product you are viewing cross references to these numbers
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
The valve stem seal, OEM part number 993 104 111 02 (sometimes superseding 993 104 111 01), is a component for the Porsche 993 series.
These seals are installed around the valve stems and serve to regulate, not entirely block, oil flow into the combustion chamber. They wipe excess oil off the valve stems and prevent undue oil burning or plug fouling. They are applicable across various 993 configurations—including the naturally aspirated Carrera and the Turbo variants—for 1994–1998 models.
Fits:- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
Why You Should Replace Them
Over time, valve stem seals, typically rubber or elastomeric, can harden, crack, or shrink, especially under high heat and engine age—which compromises their sealing effectiveness.
Visible Symptoms:
- Blue exhaust smoke, particularly upon a cold start—leftover oil seeps past hardened seals and burns in the combustion chamber.
- Increased oil consumption without noticeable external leaks, as oil is being burned rather than escaping visibly.
- Smoke or puffing at idle or after deceleration, when high vacuum draws oil past failing seals.
- Compression or misfiring issues—oil-fouled spark plugs can disrupt ignition, and carbon buildup may mimic compression loss.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99310411102
The product you are viewing cross references to these numbers
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
Fits:
Porsche 911 - 1965 to 1968
Diagram ref no 53
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90174155300
The product you are viewing cross references to these numbers
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
Fits:
Porsche 911 2.0ltr - 1965 to 1968
Porsche 912 - 1965 to 1968
This listing refers specifically to the upper bracket. For reference, the part number for the lower bracket is 90134773401 (No. 47 in the diagram). Additionally, there is a sealing ring located in the middle with part number 90134773600 (No. 46 in the diagram).
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
90134773301
The product you are viewing cross references to these numbers
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
also known are Engine Crankshaft Position Sensor
The engine crankshaft position sensor (CPS) is a critical component that monitors the crankshaft’s position and rotational speed. It sends this data to the engine control unit (ECU), allowing precise control of fuel injection, ignition timing, and other key engine functions. Without accurate input from the CPS, the ECU cannot properly synchronize spark or fuel delivery—leading to poor performance or even a no-start condition.
Crankshaft sensors typically use magnetic or Hall-effect technology:
Magnetic sensors generate a signal with a coil and magnet as the crankshaft rotates.
Hall-effect sensors detect changes in the magnetic field using a semiconductor for highly accurate readings.
Depending on the engine design, the CPS is usually located near the crankshaft pulley, harmonic balancer, flywheel, or transmission. It reads notches or teeth on a tone wheel to create a signal the ECU can interpret.
Over time, heat, vibration, and contaminants (oil, dirt, or metal shavings) can cause the sensor to fail. When this happens, common symptoms include engine stalling, rough idling, misfires, or a no-start condition.
Fits:- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
Common Symptoms of a Failing Crankshaft Position Sensor
· No Start Condition – If the ECU doesn’t receive a proper signal, the engine won’t start.
· Stalling When Warm – The sensor may fail when the engine reaches operating temperature, causing unexpected stalling.
· Erratic or Dead Tachometer – In some vehicles, a faulty CPS can cause the tachometer to behave irregularly.
· Check Engine Code P0335 – A failed internal circuit may trigger this code, though not always.
· Poor Performance at Certain RPMs – Timing issues can cause hesitation, especially at idle or higher RPMs.
· Multiple Cylinder Misfires – Unlike a single bad coil or injector, CPS failure can cause misfires across all cylinders.
This crankshaft sensor is designed for Porsche 911 G models produced between 1984 and 1989. It serves as a pulse generator, transmitting engine speed data to the DME, and is a frequent culprit when the engine experiences irregular performance.
Identified by the Bosch number ending in 005, this sensor was installed in pairs within the vehicle. A reliable and precise pulse generator is crucial for optimal engine electronics performance.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160621502
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche Boxster T 718 2.0L Manual (300 Bhp)
- Porsche Boxster T 718 2.0L PDK (300 Bhp)
- Porsche Boxster GTS 718 2.5L Manual (365 Bhp)
- Porsche Boxster GTS 718 2.5L PDK (365 Bhp)
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
- Porsche Cayman T 718 2.0L Manual (300Bhp)
- Porsche Cayman T 718 2.0L PDK (300 Bhp)
- Porsche Cayman GTS 718 2.5L Manual (365 Bhp)
- Porsche Cayman GTS 718 2.5L PDK (365 Bhp)
Kit Includes - Ignition Coil x 4
Fits:
Porsche 718 (982) Boxster 2.0L 2017>>
Porsche 718C (982C) Cayman 2.0L 2017>>
Porsche 718C (982C) Cayman 2.5L 2017>>
Porsche 718 (982) Boxster 2.5L 2017>>
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0PB905093F
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) TURBO S 1994-97
The suspension control arms connect the suspension and steering knuckle to the chassis and allow the suspension to move and articulate over bumps and road imperfections. This kit also includes the sub-frame bushes.
Control arms utilize bushings and ball joints to make these connections and those are the parts of the control arm that wear out and fail. Worn ball joints and bushings will cause vibration and clunking when driving, uneven tire wear, cause the vehicle to pull in one direction, and increase stopping distances.
This control arm kit will restore the handling and driving performance of your 993. Included in our kit are the rear control arms for the left and right sides.
Fits:
Porsche 993 (911) C2 1994 - 1997
Porsche 993 (911) C4 1994 - 1997
Porsche 993 (911) C2S 1994 - 1997
Porsche 993 (911) C4S 1994 - 1997
Porsche 993 (911) TURBO 1994 - 1996
Porsche 993 (911) TURBO S 1994 - 1997
Diagram ref No 3, 4, 5, 6 and bushes for number 2
Suspension Control Arm Kit
Control arms are crucial link in a vehicle's suspension connecting the suspension to a vehicle's subframe. These pieces are usually hinged to allow for suspension to travel and articulate as the vehicle rides over obstructions in the road and while the vehicle turns. Many vehicles such as those with independent suspensions have multiple links and feature several connection points and arms to offer better ride quality and comfort.
As bushings and joints in a control arm begin to wear you may notice a looseness feel in your suspension. And while many arms have replaceable and serviceable individual components, many still require the replacement of the entire arm.
Suspension Control Arm Kit Failure Symptoms
Play in suspension joints where these arms meet the subframe and/or knuckle Buckling noise emanating from the suspension Uneven tire wear Inability to properly align vehicle Shutter or vibration coming from the steering wheel at highway speed Wandering or pulling sensation from side to side felt on the steering wheel.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
SUSPENSIONKIT993
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 991.2 Carrera 2 3.0L (370 Bhp) 2016-19
- Porsche 991.2 Carrera 2S 3.0L (420 Bhp) 2016-19
- Porsche 991.2 Carrera 4 3.0L (370 Bhp) 2016-19
- Porsche 991.2 Carrera 4S 3.0L (420 Bhp) 2016-19
- Porsche 991.2 Cabriolet 2 3.0L (370 Bhp) 2016-19
- Porsche 991.2 Cabriolet 2S 3.0L (420 Bhp) 2016-19
- Porsche 991.2 Cabriolet 4 3.0L (370 Bhp) 2016-19
- Porsche 991.2 Cabriolet 4S 3.0L (420 Bhp) 2016-19
- Porsche 991.2 Targa 4 3.0L (370 Bhp) 2016-19
- Porsche 991.2 Targa 4S 3.0L (420 Bhp) 2016-19
- Porsche 992.1 Carrera 2 3.0L 2019-24
- Porsche 992.1 Carrera 4 3.0L 2019-24
- Porsche 992.1 Carrera 2 Cabriolet 3.0L 2019-24
- Porsche 992.1 Carrera 4 Cabriolet 3.0L 2019-24
- Porsche 992.1 Carrera 2S / GTS 3.0L 2019-24
- Porsche 992.1 Carrera 4S / GTS 3.0L 2019-24
- Porsche 992.1 Carrera 2S / GTS Cabriolet 3.0L 2019-24
- Porsche 992.1 Carrera 4S / GTS Cabriolet 3.0L 2019-24
- Porsche 992.1 Targa 4 3.0L 2020-24
- Porsche 992.1 Targa 4S / GTS 3.0L 2020-24
- Porsche 992.1 Turbo 3.8L 2020-24
- Porsche 992.1 Turbo S 3.8L 2020-24
- Porsche 992.1 Turbo Cabriolet 3.8L 2020-24
- Porsche 992.1 Turbo S Cabriolet 3.8L 2020-24
- Porsche 992.2 Carrera 2 3.0L 2024>>
- Porsche 992.2 Carrera 2 3.0L Cabriolet 2024>>
Kit Includes - Ignition Coil x 6
Fits:
Porsche 991.2 Carrera MKII 2017>>
Porsche 992.1 Carrera 3.0L MKI 2019>>
Porsche 992.1 Turbo MKI 2019>>
Porsche 992.2 Carrera 2 3.0L MKII 2024>>
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
0PB905093F
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
Fits:
Porsche 924S 2.5L 1986-88
Diagram Ref No 13.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
94460620100
The product you are viewing cross references to these numbers
- Porsche 955 Cayenne 3.2L V6 2003-06
- Porsche 955 Cayenne S 4.5L V8 2003-06
- Porsche 955 Cayenne Turbo 4.5L 2003-06
- Porsche 955 Cayenne Turbo S 4.5L 2006>>
- Porsche 957 Cayenne 3.6L 2007-10
- Porsche 957 Cayenne S/GTS 4.8L 2007-10
- Porsche 957 Cayenne Turbo / Turbo S 4.8L 2007-10
There are two types of filters one for normal air with Ref No. 95511013100 and the other for counties with dust-laden air Ref No. 95511013110
Fits:
Porsche 955 Cayenne MKI & 957 Cayenne MKII
Optimize your Porsche 955 MKI Cayenne / 957 MKII Cayenne with our premium air filter, designed to deliver top-notch performance and superior engine protection. Crafted specifically for these Porsche models, our air filter enhances airflow, promoting optimal combustion and fuel efficiency. Say goodbye to dust and contaminants that can compromise your engine's lifespan. Elevate your driving experience with improved horsepower and acceleration. Upgrade to our precision-engineered air filter for the Porsche 955 MKI Cayenne / 957 MKII Cayenne – the perfect blend of performance and protection. Trust in our product to keep your luxury vehicle running at its peak, and take the first step towards a smoother, more efficient ride.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95511013110
The product you are viewing cross references to these numbers
This kit is comprised of the following items:
- Porsche 992.1 Carrera 2 3.0L 2019-24
- Porsche 992.1 Carrera 4 3.0L 2019-24
- Porsche 992.1 Carrera 2 Cabriolet 3.0L 2019-24
- Porsche 992.1 Carrera 4 Cabriolet 3.0L 2019-24
- Porsche 992.1 Carrera 2S / GTS 3.0L 2019-24
- Porsche 992.1 Carrera 4S / GTS 3.0L 2019-24
- Porsche 992.1 Carrera 2S / GTS Cabriolet 3.0L 2019-24
- Porsche 992.1 Carrera 4S / GTS Cabriolet 3.0L 2019-24
- Porsche 992.1 Targa 4 3.0L 2020-24
- Porsche 992.1 Targa 4S / GTS 3.0L 2020-24
- Porsche 992.1 Speedster 4.0L 2019-24
- Porsche 992.1 Turbo 3.8L 2020-24
- Porsche 992.1 Turbo S 3.8L 2020-24
- Porsche 992.1 Turbo Cabriolet 3.8L 2020-24
- Porsche 992.1 Turbo S Cabriolet 3.8L 2020-24
- Porsche 992.1 GT3 4.0L / 992 S/T 4.0L 2021-24
Fits
Porsche 992 Carrera / Carrera 4
Porsche 992 Carrera S / Carrera 4S
Porsche 992 turbo
Porsche 992 GT3
Includes:
2 x Air Con Radiators
4 x Rubber O-rings for radiators
1 x Desiccator
2 x Rubber O-rings for desiccator
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
AIRCONKIT13
The product you are viewing cross references to these numbers
This kit is comprised of the following items: